Bee Ready Rod holders

BEE READY World's Best Rod Holders

KB. Removable Riser with the non-breakable ABS Nylon Base Mount…..$15.00

This new base is totally unbreakable. Riser slides in and out of

mount so that rod holder and riser can be easily removed and

stored away. Base comes with a set screw that holds the riser in.

Get multiple bases and move the holders around your boat or from boat to boat.

The Riser is 18 inches tall. Taller ones can be ordered special for $5 extra, see below.

KBE. Removable Riser Extended Length with the ABS Nylon Base Mount…..$20.00

Same as above but specially made taller. Specify length via email.

(click on picture for close-up)

M. Float Noodle for Riser...................…..…….………$ 2.00

Yellow Noodle slides over riser rod to be used for

jigs, hooks or leaders & it floats if dropped in water.

Doug “Tex” Elliott, (817-988-5468) Lake Lavon Catfish Guide says….

“I have been using the noodles on my rod holders for a while....because they are a great

place to put some already made up leaders.....put a rubber band on the bottom and it

will keep the line in order...works like a charm.”

__________________________________________________________________________________

(click on picture for close-up)

N. Riser Rod only ..............................…..…….………$ 7.50

Riser only without the base. 18 inches tall.

NE. Riser Rod only (24 inches tall)........….….………$ 12.50

Riser only without the base. 24 inches tall.

PB. Non-breakable ABS Nylon Mount Base w/Stainless Steel Hardware......…$7.50

Can be mounted on your boat in two different ways. Bolted on or

with Lag Screws. Lag screws included. Install multiple bases

on your boat to have multiple locations for your risers.

________________________________________________________________________________________

Q2.0. Pedestal Mount ................2 inch "C" Clamp for pole....…$35.00

Can be mounted on your boat without drilling any holes. Clamp onto any

existing seat pedestal. Heavy duty non-rusting aluminum holds the base

in place for a riser and any two rod, three rod or four rod holder.

You will need to buy the black base (PB) separately above.

Comes standard with a 2 inch wide stainless steel hardware "C" clamp

and has wing nuts for easy on and off installation. It is 23 inches long

from pedestal to riser.

You can order this with a 2 1/2 inch "C" clamp below.

(Rod Holder, Riser and Base shown are sold separately).

Q2.5. Pedestal Mount ............2 1/2 inch "C" Clamp for pole....…$35.00

Same as above but with 2 1/2 inch "C" Clamp for the larger seat poles.

You will need to buy the black base (PB) separately above.

QC. 2 1/2 inch wide "C" Clamp only.........................................12.00

Clamp is for wider Pedestal Poles and attaches to the

Pedestal Mount Q2.0 above .

K. Removable Riser with Aluminum Base Mount…..$20.00

Riser slides in and out of mount so that rod holder and riser can be

easily removed and stored away. Get multiple bases and move the

holders around your boat or from boat to boat. (Four Rod holder

shown, and sold separate.) The Riser is 18 inches tall.

Taller ones can be custom ordered special, just send me an

email when you order.

P. Aluminum Mount Base w/Stainless Steel Hardware.....…$12.50

Can be mounted on your boat in three different ways. You receive

the stainless steel hardware for all three options (2 bolts for bolting

the base on deck or on the side of the gunwale, and 4 lag screws for

decks you cant get underneath with. click here for more

information.

Use multiple bases to have multiple locations for your risers.

or you may contact me direct 214-354-9570 or

email me with any questions ed@ProAnglerTackle.com

I accept all major credit cards or PayPal

or I can take orders over the phone.

Dimensions